Pilot RC
PRC P47D-P01-ER

P-47D 95" 2.41m 1/5th Scale Engine Ready ARF, with Retracts, Lights, Servos & Cockpit, Jeanie Scheme

P-47D 95" 2.41m 1/5th Scale Engine Ready ARF, with Retracts, Lights, Servos & Cockpit, Jeanie Scheme

Factory Order
$4,999.00
$400.00 Flat Rate Truck Freight to Commercial Addresses (48 States)
Add $100 for Residential Delivery - Inspection Required: Click Here

Pilot RC 1/5th Scale P-47D 95" 2.41m ARF Gas Airplane, Jeanie Scheme
Engine Ready Version (see description) with Retracts, Servos, Nav Lights, Wingbag and more...

Includes: Electric Retract Gear, Navigator Lighting System, Cockpit Set, (2) Bombs/Brackets, Drop Tank, Gear Door, Fuel Tank/Dot/Vent, Wingbag, Cockpit Set, Hardware, Servo Extension Wire

Includes all the same components and pre-installation as the Landing Gear Combo, plus adds x11 Pilot-RC servos and multi-wire connectors (for aileron, flap, retract, nav lights, and bomb drop) all installed at the factory. Requires engine of choice and throttle servo. Appropriate scale spinner can be added.


Residential Addresses Require An Additional $100 Delivery Charge - Box Dims: 74x24x24, 58lbs (26kg)
Click Here for Delivery Inspection Requirements


Presenting Pilot-RC’s first composite scale warbird! It could be no other than the fantastic P47, specifically, the P47D variant. With its instantly recognizable lines and large wing for friendly handling it is ideal both as crown jewel and everyday hack. Designed around popular engine sizes, we have tested our P47D both with the straight forward single cylinder DA85, and also with the more scale like three cylinder Saito 90R3 with outstanding results. Needing a very short takeoff roll, and no wing waggle, this model will inspire confidence from day one.

  • Full scale detail with rivets, panel lines, simulated hatches, etc…
  • Full composite construction, lightweight and strong
  • Two piece wing and two piece stabilizer, all for easy transport
  • Painted outside the mold so no seam lines
  • Fully hidden linkages except rudder horn. No other horns, servo arms, ball links or pushrods are exposed
  • Pre-installed gear door
  • Pre-installed hinges
  • Battery support included, allows for the mounting of batteries to the inside of the firewall to easily help achieve the correct center of gravity
  • Patented quick assembly system for wings
  • The cowl can fit Satio 90R3 (or other similar 250mm diameter radial engines)
  • 50-85cc single cylinder two stroke engine is also easy to install
  • Removable engine box can fit different engine
  • Ample room to easily install canisters if desired
  • Elevator and rudder servos mounted mid-fuselage to avoid the need for nose weight
  • A single rudder servo controls both rudder and tail wheel, both by pull pull system
  • Tail gear door operates (open/close) without need of a dedicated servo
  • Single servo controls both elevator half.
  • Option for smoke tank

INCLUDED HARDWARE:

  • Complete air frame (including aluminum wing-tubes and fiberglass control horns)
  • Servo extension leads
  • Fuel tank (700ml) and fuel tubing pre-prepared, fuel dot and breather valve
  • Pre-prepared pushrods with ball links
  • Pre-glued and painted control horns
  • Two simulated bombs and their brackets. Can be dropped individually. The brackets can be attached or removed two bolts each.
  • Please note: If intending to release the bombs in flight, these will first need to have extra ballast added to them.
  • Simulated drop tank, easily installed using a single bolt.
  • Scale antenna
  • Center of Gravity measurement system
  • Wingspan: 94.9" (2,411mm)
  • Length: 75.6" (1,920mm)
  • Wing area: 1,685 in sq (10,870cm2)
  • Weight: 40.7lbs (18.5kg) with Saito 90R3 engine, electric starter and all accessories
  • Engine: Two stroke motor: 50-88cc or Four stroke motor: 80cc or similar size radial engine

Servos: 9 total (+2 optional)

  • x2 Super high torque (minimum 40kg). Uses x1 per flap.
  • x4 High torque (minimum 27kg). Uses x1 per aileron, x1 for elevator, x1 for rudder
  • x3 Mid size servo (35x15x30mm). Uses x2 for the gear doors and x1 for throttle
  • +2 Optional mid size servo (35x15x30mm) for the bomb drop.

Note: Due to constant design improvements Pilot RC reserves the right to change and modify design specifications without notice. Pilot's goal is to provide you with the highest performing airframes in the world using the latest technology, building techniques and materials.