10-Amp Pro Brushless ESC

with Advanced Programming and BEC

• Up to 10 amps continuous current with proper air flow
• Programmable motor braking
• Safe power-arm mode prevents accidental starts
• Programmable low voltage cut-off with settings for 2-cell Li-Po (6V), 3-cell Li-Po (9V) or 70% of battery starting voltage
• Programmable throttle input range (1.1ms-1.9 ms or Auto Select)
• Soft start
• Auto motor shut down if signal is lost or there is interference
• Programmable timing - 2 user selectable ranges for use with a large variety of brushless motors
• Pre-wired connectors - JST on battery input and 2mm female gold bullets on motor output leads

Top of page

20-Amp Brushless ESC Version 2

For Unparalleled Sensorless Brushless Performance

• Automatically selects cutoff voltage for 2- to 3-cell Li-Po batteries (6V/9V)
• Automatically sets correct motor timing
• Safe power-on mode prevents accidental starts
• Programmable braking (on/off)
• 1.5A Battery Eliminator Circuit (BEC) to power radio & servos
• Includes gold connectors for your motor

Top of page

25-Amp Pro Brushless ESC

with Advanced Programming and Heat Sinks

• Finned heat sinks for both the motor drive mosfets and dual BEC regulators to support up to 4 sub-micro servos.
• Programmable features such as low voltage cut-off, breaking, timing, and throttle input range.
• Bonus: Includes EC3 Battery Connector
• Up to 25 amps continuous current with proper air flow
• Programmable motor braking
• Safe power-arm mode prevents accidental starts
• Programmable low voltage cut-off with settings for 2-cell Li-Po (6V), 3-cell Li-Po (9V) or 70% of battery starting voltage
• Soft start
• Auto motor shut down if signal is lost or there is interference
• Programmable timing - 2 user selectable ranges for sue with a large variety of brushless motors
• Pre-wired connectors - E-flite EC3 on battery input and 3.5mm female gold bullets on motor output leads.

Top of page

40-Amp Brushless ESC Version 2

Features include auto-select cutoff voltage that automatically recognizes Li-Po batteries, programmable braking, thermal overoad protection, Battery Eliminator Circuit (BEC), advanced software and more.

Top of page

40-Amp Pro Switch-Mode BEC Brushless ESC

• Up to 40A continuous current with proper air flow, with 55A burst current (15 seconds)
• 5V switch-mode BEC circuit capable of 2.5A continuous current on any recommended input voltage
• Drive up to 7 analog or 6 digital standard-sized servos with the BEC on any recommended input voltage
• 3–6S Li-Po, 9- to 18-cell Ni-Cd/Ni-MH input voltage
• Finned heat sinks
• Programmable motor braking
• Safe power-arm mode prevents accidental starts
• Programmable low voltage cut-off with settings for 3S Li-Po (9V), 4-cell Li-Po (12V), 5-cell Li-Po (15V), 6-cell Li-Po (18V), or 70% of battery starting voltage
• Programmable soft start for helis and airplanes
• Auto motor shutdown if signal is lost or there is interference
• Programmable timing—5 user-selectable ranges for use with a large e variety of brushless motors
• Programmable throttle input range (1.1–1.9ms or 1.2–1.8ms)
• Heli mode for starting the motor with a low speed ratio
• Utilizes new smaller Mosfets technology to save weight
• Radio System Power On/Off Switch
• Pre-wired connectors—E-flite® EC3 on battery input and 3.5mm female

The E-flite 40A Pro Switch-Mode BEC Brushless ESC is a high-quality, innovative and efficient sensorless brushless electronic speed control with an integrated switch-mode BEC. It can operate without the need for a separate receiver battery to power your servos and receivers, saving you weight and complication. It is capable of up to 40 amps continuous current when using 3- to 6-series Li-Po battery packs. You can drive up to 7 analog or 6 digital standard-sized servos with the BEC on any recommended input voltage. This ESC also features an exposed, finned heat sink aluminum case with lightweight plastic endcaps. Additional features include safe power arming along with advanced programmable features such as low voltage cutoff, braking, timing, throttle input range, and more, making this truly a ‘pro series’ speed control.

Top of page

60-Amp Pro Switch-Mode BEC Brushless ESC

• Up to 60A continuous current with proper air flow with 75A peak
• 5V swich-mode BEC circuit capable of 2.5A continuous current on any recommended input voltage
• Drives up to 7 analog or 6 digital standard sized servos, with the BEC, on any recommended input voltage
• 3-6S Li-Po, 9- to 18-cell Ni-Cd/Ni-MH input voltage
• Finned heat sinks
• Programmable motor braking
• Safe power-arm mode prevents accidental starts
• Programmable low voltage cut-off with settings for 3-cell Li-Po (9V), 4-cell Li-Po (12V), 5-cell Li-Po (15V), 6-cell Li-Po (18V), or 70% of battery starting voltage
• Programmable soft start for helis and airplanes
• Auto motor shut down if signal is lost or there is interference
• Programmable timing - 5 user selectable ranges for use with a larger variety of brushless motors
• Programmable throttle input range (1.1ms–1.9ms or 1.2m–1.8ms)
• Utilizes new smaller mosfets technology to minimize weight
• Radio System Power On/Off Switch
• Optional RS232 Serial Link available for programming
• Pre-wired connectors - E-flite EC3 on battery input and 3.5mm female gold bullets on motor output leads

Top of page